high strength customized synchronous wheel pulley belt
Physical features of belt
Trapezium tooth | |||||
Item | MXL | XL XXL | L | H | XH |
tensile strength (N/mm)≥ | 45 | 80 | 120 | 270 | 380 |
Reference force(N/mm) | 35 | 60 | 90 | 220 | 300 |
Stretching rate % ≤ | 4.0 | ||||
Hardness of the back(Shore a) | 75+5 | ||||
Fabric adhesion strength (N/mm)≥ | / | 5 | 6.5 | 8 | 10 |
Main core adhesion strength N≥ | / | 200 | 380 | 600 | 800 |
Teeth cutting strength (N/mm)≥ | / | 50 | 60 | 70 | 75 |
Trapezium tooth | |||||
Item | XXH | T2.5 | T5 AT5 | T10 AT10 | T20 AT20 |
tensile strength (N/mm)≥ | 450 | 45 | 80 | 270 | 380 |
Reference force(N/mm) | 360 | 35 | 60 | 220 | 300 |
Stretching rate % ≤ | 4.0 | ||||
Hardness of the back(Shore a) | 75+5 | ||||
Fabric adhesion strength (N/mm)≥ | 12 | / | 5 | 8 | 10 |
Main core adhesion strength N≥ | 1500 | / | 200 | 600 | 800 |
Teeth cutting strength (N/mm)≥ | 90 | / | 50 | 70 | 75 |
Round arc tooth | ||||||
Item | 2M S2M | 3M S3M | S4.5M 5M S5M | 8M S8M | 14M S14M | 20 M |
tensile strength (N/mm)≥ | 45 | 90 | 160 | 300 | 400 | 520 |
Reference force(N/mm) | 35 | 70 | 130 | 240 | 320 | 410 |
Stretching rate % ≤ | 4.0 | |||||
Hardness of the back(Shore a) | 75+5 | |||||
Fabric adhesion strength (N/mm)≥ | / | / | 6 | 10 | 12 | 15 |
Main core adhesion strength N≥ | / | / | 400 | 700 | 1200 | 1600 |
Teeth cutting strength (N/mm)≥ | / | / | 50 | 60 | 80 | 100 |
Note: The tensile strength value is measured by the cut section of belt. If measure by a belt in circle, shall divide the number by 2 and then compare.
Width standard for different types of belt
Mode | MXL | XL | L | ||||||
Belt width | Code | 012 | 019 | 025 | 025 | 031 | 037 | 050 | 075 |
Width | 3.0 | 4.8 | 6.4 | 6.4 | 7.9 | 9.5 | 12.7 | 19.1 |
Mode | L | H | XH | ||||||
Belt width | Code | 100 | 075 | 100 | 150 | 200 | 200 | 300 | 400 |
Width | 25.4 | 19.1 | 25.4 | 38.1 | 50.8 | 50.8 | 76.2 | 101.6 |
Mode | XXH | T2.5 | T5/AT5 | ||||||
Belt width | Code | 200 | 300 | 400 | 500 | 4 | 6 | 10 | 6 |
Width | 50.8 | 76.2 | 101.6 | 127.0 | 4 | 6 | 10 | 6 |
Mode | T5 AT5 | T10 AT10 | T20/AT20 | ||||||
Belt width | Code | 10 | 16 | 25 | 16 | 25 | 32 | 50 | 32 |
Width | 10 | 16 | 25 | 16 | 25 | 32 | 50 | 32 |
Mode | T20 AT20 | 3M S3M | 5M S4.5M S5M | ||||||
Belt width | Code | 50 | 75 | 100 | 6 | 9 | 15 | 9 | 15 |
Width | 50 | 75 | 100 | 6 | 9 | 15 | 9 | 15 |
Mode | 5M S4.5M S5M | 8M S8M | 14M S14M | ||||||
Belt width | Code | 25 | 30 | 30 | 40 | 50 | 85 | 55 | 85 |
Width | 25 | 30 | 30 | 40 | 50 | 85 | 55 | 85 |
Mode | 14M S14M | 20M | ||||||||
Belt width | Code | 115 | 170 | 70 | 85 | 115 | 170 | 230 | 290 | 340 |
Width | 155 | 170 | 70 | 85 | 155 | 170 | 230 | 290 | 340 |
Industrial synchronous belt with trapezium tooth
Mode | Pitch Pb | Tooth height ht | Belt thickness hs | Angle 2β° |
MXL | 2.032 | 0.51 | 1.14 | 40 |
XL | 5.080 | 1.27 | 2.30 | 50 |
L | 9.525 | 1.91 | 3.60 | 40 |
H | 12.70 | 2.29 | 4.30 | 40 |
XH | 22.225 | 6.35 | 11.20 | 40 |
XXH | 31.750 | 9.53 | 15.70 | 40 |
T2.5 | 2.5 | 0.7 | 1.30 | 40 |
T5 | 5 | 1.2 | 2.20 | 40 |
T10 | 10 | 2.50 | 4.50 | 40 |
T20 | 20 | 5.00 | 8.00 | 40 |
AT5 | 5 | 1.20 | 2.70 | 50 |
AT10 | 10 | 2.50 | 5.00 | 50 |
AT20 | 20 | 5.00 | 8.00 | 50 |
Industrial synchronous belt with round arc tooth
HTD round arc tooth | STPD/STS round arc tooth | RPP/HPPD round arc tooth |
Code | Mode | Pitch Pb | Tooth height ht | Belt thickness hs |
HTD | 3M | 3 | 1.17 | 2.4 |
5M | 5 | 2.06 | 3.8 | |
8M | 8 | 3.36 | 6.00 | |
14M | 14 | 6.02 | 10.00 | |
20M | 20 | 8.4 | 13.20 | |
STPD/STS | S2M | 2 | 0.76 | 1.36 |
S3M | 3 | 1.14 | 1.9 | |
S4.5M | 4.5 | 1.71 | 2.81 | |
S5M | 5 | 1.91 | 3.4 | |
S8M | 8 | 3.05 | 5.3 | |
S14M | 14 | 5.3 | 10.2 | |
RPP/HPPD | P2M | 2 | 0.76 | 1.36 |
P3M | 3 | 1.15 | 1.9 | |
P5M | 5 | 1.95 | 3.5 | |
P8M | 8 | 3.2 | 5.5 | |
P14M | 14 | 6.00 | 10 |
Write your message here and send it to us
Related News